Land Rover Forums - Land Rover Enthusiast Forum - Search Results

Search: Posts Made By: vanbadri
Showing results 1 to 17 of 17
Search took 0.01 seconds.
Forum: Discovery I
09-18-2018, 10:54 AM
Replies: 15
Views: 532
Posted By Paul Grant

There is nothing like that in the DI. You have...

There is nothing like that in the DI. You have the alarm module located under the dash behind the glove box. There is an antenna wire that runs from that module up the right a pillar behind the...
Forum: Discovery I
09-13-2018, 02:00 PM
Replies: 3
Views: 262
Posted By Crunkgringo

Before I did my complete engine rebuild I...

Before I did my complete engine rebuild I replaced the main and rod bearings with the motor in place. I used the write up on the D2 as they are basically the same rotating assembly. The difference...
Forum: Discovery I
09-13-2018, 12:00 PM
Replies: 3
Views: 262
Posted By ihscouts

Pretty common practice to replace shells without...

Pretty common practice to replace shells without machine work. Measure a journal. If your getting rod knock now it won't take much to spin a bearing under load and then you can toss the crank in the...
Forum: Discovery I
08-09-2018, 01:41 PM
Replies: 8
Views: 548
Posted By partsguru

https://cimg4.ibsrv.net/gimg/landroverforums.com-v...

https://cimg4.ibsrv.net/gimg/landroverforums.com-vbulletin/1842x1080/80-2_222dbedccec0596e0e572d28ba17b77f09829f10.jpg...
Forum: Discovery I
08-06-2018, 07:21 AM
Replies: 7
Views: 497
Posted By WaltNYC

Check this out. It may answer your question... ...

Check this out. It may answer your question...

https://landroverforums.com/forum/discovery-i-39/rear-cargo-door-latch-87279/
Forum: Discovery I
08-06-2018, 12:36 AM
Replies: 10
Views: 641
Posted By Ankeneering

Make sure the ECU isn't getting wet. Its located...

Make sure the ECU isn't getting wet. Its located right at the hood fender seam on the passenger side of the engine compartment. The plastic box covering mine wasn't firmly attached and after a hard...
Forum: Discovery I
07-17-2018, 03:50 PM
Replies: 14
Views: 1,111
Posted By hrhoward

I drive mine 60+ miles a day M-F. Has over 258K...

I drive mine 60+ miles a day M-F. Has over 258K on it (I've put over 46k on it in three-ish years). I have replaced a bunch of stuff on it to get it road worthy after I drug it out of PO's garage,...
Forum: Discovery I
07-16-2018, 04:57 PM
Replies: 14
Views: 1,111
Posted By Sixpack577

Fire extinquisher

Fire extinquisher
Forum: Discovery I
06-07-2018, 10:20 AM
Replies: 6
Views: 624
Posted By Paul Grant

I'd put money on a bad ecu. I don't even bother...

I'd put money on a bad ecu. I don't even bother reselling the DI ECU anymore. Too many failures. Remove the ECU, it's a silver box about the size of a cigarette pack, behind the glove box. Open...
Forum: Discovery I
06-05-2018, 09:35 AM
Replies: 6
Views: 624
Posted By WaltNYC

from etc manual page 80 CEL disable of...

from etc manual page 80



CEL disable of cruise control only applies on 300 Tdi's.
Forum: Discovery I
06-03-2018, 08:48 PM
Replies: 3
Views: 473
Posted By Icannap1

Tap on it with a rubber mallet side to side and...

Tap on it with a rubber mallet side to side and it will just pull out.
Forum: Discovery I
06-03-2018, 08:10 PM
Replies: 3
Views: 473
Posted By stillruns

i have no idea as to the answer but iíll comment...

i have no idea as to the answer but iíll comment to help keep the thread going. There are plenty of folks here who know the answer. Have you looked at the RAVE manual?
Forum: Discovery I
05-24-2018, 03:18 PM
Replies: 6
Views: 631
Posted By rjlsierra

x2 on that,it worked so well for me that i left...

x2 on that,it worked so well for me that i left it that way and haven't had the water sounds since.since there are no inline valve the heater core doesn't know the difference,but if you do disconnect...
Forum: Discovery I
05-24-2018, 03:07 PM
Replies: 6
Views: 631
Posted By FloridaRover

Swap the heater hoses and run it for a day or so,...

Swap the heater hoses and run it for a day or so, then swap back. Works well for me.
Forum: Discovery I
04-05-2018, 02:46 PM
Replies: 4
Views: 326
Posted By DavC

The joints are sized so there is no movement of...

The joints are sized so there is no movement of the joint and its caps in the yokes beyond the intended rotational movement. Post install all I have done is grease them up, then run the car for a...
Forum: Discovery I
04-04-2018, 09:34 AM
Replies: 1
Views: 353
Posted By grenade

14mm OD 11mm ID 1.5mm cross section. ...

14mm OD
11mm ID
1.5mm cross section.

get something that is 70 or 90 durometer in hardness that is oil and heat resistant. There is 10-12 on the whole truck I believe between the oil and...
Forum: Discovery I
03-19-2018, 08:25 AM
Replies: 25
Views: 1,562
Posted By AbnMike

Look up Will Tillery - he usually has tested...

Look up Will Tillery - he usually has tested original ones.

Folks have had problems with the aftermarket ones with plastic side tanks - they can drip in freezing temps.
Showing results 1 to 17 of 17


 
Forum Jump

Advertising
Featured Sponsors
Vendor Directory