Discovery II Talk about the Land Rover Discovery II within.
Sponsored by:
Sponsored by:

2000 vs. 2003

Thread Tools
 
Search this Thread
 
Old Sep 16, 2009 | 02:43 PM
  #1  
outback96's Avatar
Thread Starter
|
Drifting
Joined: Mar 2009
Posts: 30
Likes: 0
Default 2000 vs. 2003

recently I took my father-n-law's 99 DII out for a little offroading (which is bone stock), upon approaching the obstical I noticed that 2 two outcomes where inevitable. 1) I was going to be high strong or 2) I was going to rip the front bumper off... luckily, neither of these two happened, however, I did managed to "adjust" his brush guard a little for him as I came up, over and nose first into the abyss. This got me thinking about some mod's to do to my own 2000 Disco. I have noticed that the 2003-04 front bumpers are smaller in thickness and was wondering if one could find one cheap, how much playing would one have to do to get that to mount on my 2000. The area that I live the above situation would be more common.

2000 Discovery II
132k coil/spring conversion, roof rack soon to come.
 
Reply
Old Sep 16, 2009 | 02:57 PM
  #2  
salve7's Avatar
Recovery Vehicle
Joined: Mar 2008
Posts: 755
Likes: 2
From: Sevierville TN
Default

I would say for a few bucks more you could get a better, aftermarket front bumper. Or for a cheap mod you could trim the 2000's plastic under the bumper...
 
Reply
Old Sep 16, 2009 | 03:59 PM
  #3  
Disco_Fever's Avatar
Winching
Joined: Sep 2008
Posts: 589
Likes: 4
From: Portland, OR
Default

So, in hindsight, the outcomes you forecast were in fact not inevitable... LOL

Just keep an eye out for a used bumper, or check out Nate's stuff at Bottorf Fab. He's got good prices and his stuff is a great value; looks great and tough as any!

www.bottorf-fabrication.com

Cheers!
 
Reply
Old Sep 16, 2009 | 04:04 PM
  #4  
Camdisco24's Avatar
TReK
Joined: Mar 2007
Posts: 2,172
Likes: 8
From: Asheville, NC
Default

Save for an offroad bumper, you'll be happier with that in the long run.
Like Salve said, you could trim up the bumper, we've had a handful of people on here do that, but IMO it looks a little cheesy if you also use your disco for a daily driver.
 
Reply
Old Sep 16, 2009 | 04:39 PM
  #5  
NiteTrain's Avatar
TReK
Joined: Mar 2008
Posts: 2,306
Likes: 3
From: Woodstock, GA
Default

I also say go with a aftermarket bumper, btw what do you mean by "high strong"?
 
Reply
Old Sep 16, 2009 | 05:22 PM
  #6  
outback96's Avatar
Thread Starter
|
Drifting
Joined: Mar 2009
Posts: 30
Likes: 0
Default

"high strung" is when the angle is too great for the trucks setup and you end up with 4 wheels off the ground. That's what I've always known it as. Willing to be corrected, I'm just a simple guy from NE. GA. Thanks for the suggestions, yeah after thinking about it a little more I will probably go with an aftermarket bumper.
 
Reply
Old Sep 16, 2009 | 05:32 PM
  #7  
Spike555's Avatar
Team Owner
Joined: Jun 2007
Posts: 26,212
Likes: 98
From: Grand Rapids MI
Default

We always call that high centered.
The center of the vehicle is higher than the axles.
 
Reply
Old Sep 16, 2009 | 05:56 PM
  #8  
NiteTrain's Avatar
TReK
Joined: Mar 2008
Posts: 2,306
Likes: 3
From: Woodstock, GA
Default

I'm just a simple guy from NW GA. we call it high centered over here. BTW what part of NE GA ya from?
 
Reply
Old Sep 16, 2009 | 09:09 PM
  #9  
outback96's Avatar
Thread Starter
|
Drifting
Joined: Mar 2009
Posts: 30
Likes: 0
Default

Over in Toccoa. and high centered sounds better than high strung. thanks for the correction and info.
 
Reply
Old Sep 16, 2009 | 09:20 PM
  #10  
Spike555's Avatar
Team Owner
Joined: Jun 2007
Posts: 26,212
Likes: 98
From: Grand Rapids MI
Default

My kids are high strung...
 
Reply



All times are GMT -5. The time now is 03:49 AM.