Land Rover Forums - Land Rover Enthusiast Forum
0 2020/06/02 06:51:18
0 2020/06/02 06:51:33
0 2020/06/28 14:06:12
cutout for hose. You can see the bottom former in the wing. There is another inside, above the hole too.
cutout for hose. You can see the bottom former in the wing. There is another inside, above the hole too.
0 2020/06/28 14:06:44
Cutout for the tube. Southdown provides a template. The hole is a little on the small side. I used a Dremmel tool.
Cutout for the tube. Southdown provides a template. The hole is a little on the small side. I used a Dremmel tool.
0 2020/06/28 14:08:19
The inside of the molding mounted on the tube. You will need to glue it onto the tube and to the wing.
The inside of the molding mounted on the tube. You will need to glue it onto the tube and to the wing.
0 2020/06/28 14:09:53
The A pillar mounting bracket painted and attached.
The A pillar mounting bracket painted and attached.
0 2020/06/28 14:11:16
Guide tube through the wing.
Guide tube through the wing.
0 2020/06/28 14:12:06
The other end of the guide tube in the engine bay.
The other end of the guide tube in the engine bay.
0 2020/06/28 14:12:57
The cord I will use to pull the hose through fished through the tube.
The cord I will use to pull the hose through fished through the tube.
0 2020/06/28 14:13:37
0 2020/06/28 14:14:26
The guide tube removed. This end will be tied onto the hose to pull it through the wing.
The guide tube removed. This end will be tied onto the hose to pull it through the wing.
0 2020/06/28 14:14:53
0 2020/06/28 14:15:53
After the hose has been pulled through. This didn't take too much work if the cutouts are sized correctly.
After the hose has been pulled through. This didn't take too much work if the cutouts are sized correctly.
0 2020/06/28 14:16:22
As you can see there is a generous amount of hose to work with.
As you can see there is a generous amount of hose to work with.
0 2020/06/28 14:17:33
The hose is in the reducer and the reducer is attached to the filter box with a jubilee clamp. The hose to reducer fit is not very tight. Only the sealent is what is holding them together. A steel ring on the inside and a jubilee clamp on the outside would give a more secure fit. I had to disconnect the hood sensor wires to get clearance to work.
The hose is in the reducer and the reducer is attached to the filter box with a jubilee clamp. The hose to reducer fit is not very tight. Only the sealent is what is holding them together. A steel ring on the inside and a jubilee clamp on the outside would give a more secure fit. I had to disconnect the hood sensor wires to get clearance to work.
0 2020/06/28 14:18:37
Tube mounted to A pillar
Tube mounted to A pillar
0 2020/06/28 14:22:06
The L bracket. You can see the fit between the bracket and the door frame
The L bracket. You can see the fit between the bracket and the door frame
0 2020/06/28 14:22:43
I need to work with the hole size to get the Southdown molding to fit better.
I need to work with the hole size to get the Southdown molding to fit better.
0 2020/06/28 14:24:32
The included round h
The included round h
0 2020/06/28 14:25:39
0 2020/06/28 14:43:01
The gap caused by the round headed screws.
The gap caused by the round headed screws.
0 2020/06/28 14:43:33
0 2020/06/28 14:44:15
0 2021/09/21 10:14:19
Left side
Left side
0 2021/10/11 15:08:53
right side
right side
0 2021/10/11 15:09:00
right side
right side
0 2021/10/11 15:09:08
left side
left side
0 2021/10/11 15:09:14
right side
right side
0 2021/10/11 15:09:21
left side
left side
0 2021/10/11 15:09:29
right side
right side
0 2021/10/11 15:09:36
right side
right side
0 2021/10/11 15:09:43
right side
right side
0 2021/10/11 15:09:49