Land Rover Forums - Land Rover Enthusiast Forum
0 2022/02/16 16:35:26
Much more tire on the new Nitto's on the right.
Much more tire on the new Nitto's on the right.
0 2022/02/27 12:20:51
That tire is a "Beast" to put up there.
That tire is a "Beast" to put up there.
0 2022/02/27 12:21:09
The ground slopes to the right making the Wrangler look much higher. In real life it's < than 1/2".
The ground slopes to the right making the Wrangler look much higher. In real life it's < than 1/2".
0 2022/02/27 12:21:29
Hockey puck on floor jack worked but was sketchy.
Hockey puck on floor jack worked but was sketchy.
0 2022/02/27 12:26:18
Definitely need a new setup for this crazy mount point.
Definitely need a new setup for this crazy mount point.
0 2022/02/27 12:26:34
Depending on floor jack, you may not have to do this. I have a height thing that made it more challenging.
Depending on floor jack, you may not have to do this. I have a height thing that made it more challenging.
0 2022/02/27 12:26:51
Damper on the left comes off very quickly. Also was shocked how rough the rotors were after 5,300 miles. Starting to get crazy gouges after a short haul.
Damper on the left comes off very quickly. Also was shocked how rough the rotors were after 5,300 miles. Starting to get crazy gouges after a short haul.
0 2022/02/27 12:27:06
Use a T-35 Torx bit.
Use a T-35 Torx bit.
0 2022/02/27 12:27:21
First side started with 1/16" marks on top & bottom fins. Second side started at 3/16" which was much better aiming point.
First side started with 1/16" marks on top & bottom fins. Second side started at 3/16" which was much better aiming point.
0 2022/02/27 12:31:38
Grind away until you want to cry! Wear goggles, mask, and ear protection.
Grind away until you want to cry! Wear goggles, mask, and ear protection.
0 2022/02/27 12:31:48
Also did a 1" lift. Interestingly, it doesn't take a lot of adjustment to get an additional 1". Didn't realize that it wasn't a 1:1 ratio.
Also did a 1" lift. Interestingly, it doesn't take a lot of adjustment to get an additional 1". Didn't realize that it wasn't a 1:1 ratio.
0 2022/02/27 12:31:58
From the "inside", check your gap. Don't crank down the lug nuts until you check. If it kisses, grind more. If it doesn't kiss, tighten lug nuts more. When fully torqued and I had >1/16", I was done.
From the "inside", check your gap. Don't crank down the lug nuts until you check. If it kisses, grind more. If it doesn't kiss, tighten lug nuts more. When fully torqued and I had >1/16", I was done.
0 2022/02/27 12:32:06
0 2022/02/27 12:36:41
0 2022/02/27 12:36:51
0 2022/02/27 12:37:06
0 2022/02/28 11:42:21
0 2022/03/02 07:40:58
0 2022/03/10 07:34:34
0 2022/03/10 08:04:18
Tucks right under the ladder bracket and used some stainless hardware.
Tucks right under the ladder bracket and used some stainless hardware.
0 2022/03/10 08:09:28
You could also 3M tape it here if you go JLR's way.
You could also 3M tape it here if you go JLR's way.
0 2022/03/10 08:10:29
Pull off the rubber door seal and angle here for best results. Then cross your fingers.
Pull off the rubber door seal and angle here for best results. Then cross your fingers.
0 2022/03/10 08:12:57
Horror!! Grommet on order, "After" pics soon.
Horror!! Grommet on order, "After" pics soon.
0 2022/03/10 08:14:40
Beautiful wide views...(window needs washed)
Beautiful wide views...(window needs washed)
0 2022/03/10 08:18:13
Dark, narrow chamber of death.
Dark, narrow chamber of death.
0 2022/03/10 08:18:25
Red blinky light in upper corner, never see. Tells me dashcam is on.
Red blinky light in upper corner, never see. Tells me dashcam is on.
0 2022/03/10 08:19:48
0 2022/03/10 08:20:02
Cables really disappeared well.
Cables really disappeared well.
0 2022/03/10 08:22:57
0 2022/03/11 13:30:15
0 2022/03/11 13:31:34
0 2022/03/11 13:33:17
This is where it is. That capped connector in lower right. This is on the right side of the engine compartment.
This is where it is. That capped connector in lower right. This is on the right side of the engine compartment.
0 2022/03/12 10:02:36
What the "capped" connector looks like.
What the "capped" connector looks like.
0 2022/03/12 10:02:49
A connector like this in use (I should trace it to the electrical diagram).
A connector like this in use (I should trace it to the electrical diagram).
0 2022/03/12 10:02:59
Empty and waiting for a PIN! Need to find a pin that fits in there once I identify the connector.
Empty and waiting for a PIN! Need to find a pin that fits in there once I identify the connector.
0 2022/03/12 10:03:07
0 2022/03/15 11:28:51
0 2022/03/20 11:20:06
0 2022/03/24 05:42:14
0 2022/03/28 14:11:56