Land Rover Forums - Land Rover Enthusiast Forum
He loves to travel.So much so he does not care how big a mess he and his friend created.
He loves to travel.So much so he does not care how big a mess he and his friend created.
0 2019/07/28 08:10:22
0 2019/06/27 05:23:32
0 2019/06/10 09:52:32
0 2019/06/10 09:52:21
0 2019/06/04 12:35:03
0 2019/06/04 12:32:49
2 connector plug from drivers side foot well light
2 connector plug from drivers side foot well light
0 2019/05/19 08:29:34
Pulled the rubber tube lose on the left side. (right side has the washer fluid hose and not enough room to get the cable through)
Pulled the rubber tube lose on the left side. (right side has the washer fluid hose and not enough room to get the cable through)
0 2019/05/13 15:14:53
I pushed a screw driver through first to help align the tube in a straight position. I then used a thin wire taped to the cable and pushed it through the tube. This method assures no compromise of the weather seal around the tailgate.
I pushed a screw driver through first to help align the tube in a straight position. I then used a thin wire taped to the cable and pushed it through the tube. This method assures no compromise of the weather seal around the tailgate.
0 2019/05/13 15:14:43
0 2019/05/13 15:14:32
Pulled down the door(body) seal for both front and rear doors to push the cable up into the headliner
Pulled down the door(body) seal for both front and rear doors to push the cable up into the headliner
0 2019/05/13 15:14:22
0 2019/05/13 15:14:12
Camera cable that comes down into the car
Camera cable that comes down into the car
0 2019/05/13 15:14:02
Best of all I cannot see it while driving
Best of all I cannot see it while driving
0 2019/05/13 15:13:51
Mounted right under the mirror making sure the lens was centered as best I could get it.
Mounted right under the mirror making sure the lens was centered as best I could get it.
0 2019/05/13 15:13:40
0 2019/04/10 18:39:44
0 2019/04/10 18:39:26
There is oil on and near the connector, I don't think it was sprayed up from the pan.
There is oil on and near the connector, I don't think it was sprayed up from the pan.
0 2019/04/06 09:01:49
Only the back right side of the pan is wet, so I am thinking the pan seal is still good. What do the experts think replacing the sleeve now and the fluid/filter/pan later this summer?
Only the back right side of the pan is wet, so I am thinking the pan seal is still good. What do the experts think replacing the sleeve now and the fluid/filter/pan later this summer?
0 2019/04/06 09:01:38
I started with a 4x8 sheet of white Oak Plywood and cut it into a 4x4 piece. Good this the rover had a full length Frontrunner roof rack, other than reaching up, bringing home a 4x8 sheet of plywood was an easy tack.
I started with a 4x8 sheet of white Oak Plywood and cut it into a 4x4 piece. Good this the rover had a full length Frontrunner roof rack, other than reaching up, bringing home a 4x8 sheet of plywood was an easy tack.
0 2019/03/16 13:34:34
Close up of my poor craftsman's skills., But in the end, the did fit and bolt up in place
Close up of my poor craftsman's skills., But in the end, the did fit and bolt up in place
0 2019/03/16 13:34:23
Once the basic outline is cut and sanded, I counter sunk the opening for the Land Rover tie down rings
Once the basic outline is cut and sanded, I counter sunk the opening for the Land Rover tie down rings
0 2019/03/16 13:34:12
So, I laid out the Land Rover Cargo area rubber mat and despite my lack of artistic ability, I managed to trace the outline of the mat
So, I laid out the Land Rover Cargo area rubber mat and despite my lack of artistic ability, I managed to trace the outline of the mat
0 2019/03/16 13:33:59
Here it is in place held down by the Original tie downs (I used 4 M8x1.25 x6 0mm bolts in place of the hex head one on there originally)
Here it is in place held down by the Original tie downs (I used 4 M8x1.25 x6 0mm bolts in place of the hex head one on there originally)
0 2019/03/16 13:33:08
Fridge slide installed with M8 x 1.25 x 30mm bolts into wood nuts on the bottom side of the board.
Fridge slide installed with M8 x 1.25 x 30mm bolts into wood nuts on the bottom side of the board.
0 2019/03/16 13:32:56
Here it is configured for normal use, rubber mat and all. Look almost like it was before OI started.
Here it is configured for normal use, rubber mat and all. Look almost like it was before OI started.
0 2019/03/16 13:32:40
Fridge deployed ready to give up all of that goodness that was bottles up inside
Fridge deployed ready to give up all of that goodness that was bottles up inside
0 2019/03/16 13:32:25
Fridge intalled!
Fridge intalled!
0 2019/03/16 13:32:14
ladder install
ladder install
0 2019/03/09 09:34:39
Roof Rack
Roof Rack
0 2019/03/09 09:34:27
Winddam from the front
Winddam from the front
0 2019/03/09 09:34:14
Here it is in the normal condition
Here it is in the normal condition
0 2019/03/09 09:20:30
And here it is ready to fit in the garage.
And here it is ready to fit in the garage.
0 2019/03/09 09:20:20
0 2019/01/19 11:35:14
0 2019/01/19 11:34:01
0 2019/01/12 13:56:07
0 2019/01/12 13:53:10
0 2019/01/11 06:25:58
0 2019/01/11 06:25:00
0 2019/01/11 06:14:42