Land Rover Forums - Land Rover Enthusiast Forum
Its not pretty but it worked. Getting our mig gun in there was a bit of a challenge for some of the
Its not pretty but it worked. Getting our mig gun in there was a bit of a challenge for some of the
0 2025/12/16 10:11:54
2 broken bolt on the right side
2 broken bolt on the right side
0 2025/12/16 10:11:49
4 broken bolst on the left sife of the manifold/turbo. You can see the top one sitting on it's side
4 broken bolst on the left sife of the manifold/turbo. You can see the top one sitting on it's side
0 2025/12/16 10:11:45
Only way to see the broken bolts are by removing the heat shields around the manifold. The gasket has a heat shield intergrated to it making it difficult to see without removing the shields surrounding the manifold.
Only way to see the broken bolts are by removing the heat shields around the manifold. The gasket has a heat shield intergrated to it making it difficult to see without removing the shields surrounding the manifold.
0 2025/12/16 10:11:40
0 2025/11/06 18:37:55
0 2025/11/06 18:37:53
0 2025/05/11 10:14:16
Both defender have our tailgate rack. Our is carrying a full jerry can that weighs 40lbs a propane tank that weighs 15lbs and the maxtrax extreme that weights 20lb. The rack itself weighs 40lbs and the 35s and wheel combo weight about 112lbs. Oem weighed about 75lbs
Both defender have our tailgate rack. Our is carrying a full jerry can that weighs 40lbs a propane tank that weighs 15lbs and the maxtrax extreme that weights 20lb. The rack itself weighs 40lbs and the 35s and wheel combo weight about 112lbs. Oem weighed about 75lbs
0 2025/05/11 10:14:14
0 2024/11/21 20:41:50
0 2024/09/16 07:23:37
0 2024/06/18 08:29:44
0 2024/04/23 10:19:01
0 2023/01/20 11:45:22
0 2023/01/02 13:46:10
0 2022/11/16 00:45:16
0 2022/10/03 21:28:59
For the top I use push pin clips to hold the rear liner to the front liner.
For the top I use push pin clips to hold the rear liner to the front liner.
0 2022/10/02 08:49:55
Use the holes and zip tie, to Zip tie the front fender liner onto the bumper. This picture shows how it will look installed.
Use the holes and zip tie, to Zip tie the front fender liner onto the bumper. This picture shows how it will look installed.
0 2022/10/02 08:49:48
Wrap a zip tie as shown around the bumper retaining bracket on the fender.
Wrap a zip tie as shown around the bumper retaining bracket on the fender.
0 2022/10/02 08:49:41
Make another hole where the red dot is at.
Make another hole where the red dot is at.
0 2022/10/02 08:49:36
Now move on to your bumper, after the trimming and modifications have been done (1.5" of trimming off and coolers have been relocated) locate the buldge and make another hole as circled. You can use a pick to make stab a hole in it or a drill bit. We use a pick as its easier.
Now move on to your bumper, after the trimming and modifications have been done (1.5" of trimming off and coolers have been relocated) locate the buldge and make another hole as circled. You can use a pick to make stab a hole in it or a drill bit. We use a pick as its easier.
0 2022/10/02 08:49:32
Cut out the area marked in red.
Cut out the area marked in red.
0 2022/10/02 08:49:27
This is what it should look like after folding the crease in.
This is what it should look like after folding the crease in.
0 2022/10/02 08:49:22
Cut two slits as shown. DO NOT CUT FROM EDGE TO EDGE! Uou just want to make 2 cuts a couple of inches long. You'll then use a heat gun, heat the area between the cuts, and fold the crease in. Check out the following picture for a plbetter understanding.
Cut two slits as shown. DO NOT CUT FROM EDGE TO EDGE! Uou just want to make 2 cuts a couple of inches long. You'll then use a heat gun, heat the area between the cuts, and fold the crease in. Check out the following picture for a plbetter understanding.
0 2022/10/02 08:49:18
This is what you'll have after you trim the edge off
This is what you'll have after you trim the edge off
0 2022/10/02 08:49:13
Now trim this edge off
Now trim this edge off
0 2022/10/02 08:49:08
This is what it will look like after trimming the edge off
This is what it will look like after trimming the edge off
0 2022/10/02 08:49:02
Flip the liner over and trim this edge off between the red lines.
Flip the liner over and trim this edge off between the red lines.
0 2022/10/02 08:48:56
This is what it will look like after cutting the vents off
This is what it will look like after cutting the vents off
0 2022/10/02 08:48:50
First we cut off the two vents marked with the X
First we cut off the two vents marked with the X
0 2022/10/02 08:48:43