Land Rover Forums - Land Rover Enthusiast Forum
Looking east towards blanca peak
Looking east towards blanca peak
0 2025/10/23 15:22:56
Looking west over the san luis valley
Looking west over the san luis valley
0 2025/10/23 15:22:43
Wife got this awesome picture with the lightning.
Wife got this awesome picture with the lightning.
0 2025/10/23 15:22:37
0 2025/08/31 15:36:23
0 2025/08/31 15:32:05
0 2025/08/31 15:32:02
0 2025/08/31 15:31:59
The original bumper with all the sensors attached
The original bumper with all the sensors attached
0 2025/07/11 20:11:19
Bumper removed from the Defender. The square sensors by both tires are the rear radar for detecting cross traffic
Bumper removed from the Defender. The square sensors by both tires are the rear radar for detecting cross traffic
0 2025/07/11 20:11:13
Shot showing me fixing my measuring mistake for the two holes. I think it looks pretty good. Doesn't even look like that is a 1mm piece of black plastic behind the license plate.
Shot showing me fixing my measuring mistake for the two holes. I think it looks pretty good. Doesn't even look like that is a 1mm piece of black plastic behind the license plate.
0 2025/07/11 20:10:24
Profile view before the tire carrier was removed. Sits nice and flush
Profile view before the tire carrier was removed. Sits nice and flush
0 2025/07/11 20:10:19
Wiring on the bumper all done and tucked away.
Wiring on the bumper all done and tucked away.
0 2025/07/11 20:10:14
Close up of some of the wiring you will have to do. I installed a relay to power the reverse lights. Also don't mount the key sensor as you will have to take it off to tighten the bumper bolts.
Close up of some of the wiring you will have to do. I installed a relay to power the reverse lights. Also don't mount the key sensor as you will have to take it off to tighten the bumper bolts.
0 2025/07/11 20:10:07
Bumper with holes drilled into the wrong spot. Didn't realize at the time this picture was taken. Also notice the lights aren't quite flush with the bumper. I was bummed because I thought the bracket wouldn't let them go further forward. Well dummy me didn't think it through, all I had to do was flip the bracket around.
Bumper with holes drilled into the wrong spot. Didn't realize at the time this picture was taken. Also notice the lights aren't quite flush with the bumper. I was bummed because I thought the bracket wouldn't let them go further forward. Well dummy me didn't think it through, all I had to do was flip the bracket around.
0 2025/07/11 20:09:47
0 2025/07/11 19:53:47
0 2025/07/11 19:53:44
0 2025/07/11 19:53:42
0 2025/06/06 19:30:54
0 2025/05/28 18:39:03
A picture of the liner back in after removal of the pinch weld. Need to figure out a way cover the gap so debris doesn't build up
A picture of the liner back in after removal of the pinch weld. Need to figure out a way cover the gap so debris doesn't build up
0 2025/05/28 18:27:30
Pinch weld before removal. Lucky8 and Saltek both have videos on how and what to trim. It is a little difficult to get a sawzall in there. I used a combo of sawzall and dremel with cutoff wheel.
Pinch weld before removal. Lucky8 and Saltek both have videos on how and what to trim. It is a little difficult to get a sawzall in there. I used a combo of sawzall and dremel with cutoff wheel.
0 2025/05/28 18:27:27
0 2025/05/18 14:29:30
Passenger Side
Passenger Side
0 2025/05/18 14:28:09
Driver Side
Driver Side
0 2025/05/18 14:28:06
No lift, tuffant kimberley 18 with falken wildpeak at3w
No lift, tuffant kimberley 18 with falken wildpeak at3w
0 2025/05/18 14:24:13
Lift rods, tuffant kimberley 18 with falken wildpeak at3w
Lift rods, tuffant kimberley 18 with falken wildpeak at3w
0 2025/05/18 14:24:09
Installed battery tray with mods to lift the battery up about a half inch. You can see the ribs on the wheel well just on either side of the aluminum bracket I made. Also you can how much the light comes over the top of the plate. Also not as easy to see the plat is touching the plastic bracket that holds the aux radiator. It is also touching the the coolant pipe. I put a piece of self adhesive rubber between the pipe and plate.
Installed battery tray with mods to lift the battery up about a half inch. You can see the ribs on the wheel well just on either side of the aluminum bracket I made. Also you can how much the light comes over the top of the plate. Also not as easy to see the plat is touching the plastic bracket that holds the aux radiator. It is also touching the the coolant pipe. I put a piece of self adhesive rubber between the pipe and plate.
0 2025/02/05 07:31:45
0 2025/02/05 07:30:35
Here is my 500amp relay. Left side goes to the winch. Right side is coming from the second battery. On the for left above the red area is the power take off point with my 450A fuse.
Here is my 500amp relay. Left side goes to the winch. Right side is coming from the second battery. On the for left above the red area is the power take off point with my 450A fuse.
0 2025/02/05 07:30:33
Installed battery all wired up. I also fused the second battery.
Installed battery all wired up. I also fused the second battery.
0 2025/02/05 07:30:29
Installed battery tray with mods to lift the battery up about a half inch
Installed battery tray with mods to lift the battery up about a half inch
0 2025/02/05 07:30:26
0 2025/02/02 14:40:06
0 2025/02/02 14:40:03
0 2024/09/29 18:42:23
0 2024/09/29 18:42:21
0 2024/09/29 18:42:19
0 2024/09/29 18:42:16
0 2024/09/29 18:42:14
0 2024/09/29 18:34:55
0 2024/05/27 17:34:51