3D Printable Parts Collection
#141
12-17-2022 | 07:53 AM
2nd Gear
Joined: Dec 2022
Posts: 2
Likes: 0
#142
02-11-2023 | 05:06 PM
Drifting
Joined: Feb 2023
Posts: 35
Likes: 4
List of parts I'm working on
known as Center Air Intake Moulding JAK000010PMA MSRP $319 estimated cost to reproduce is about $150 or less
https://www.roverparts.com/body-chas...JAK000010PMAG/
Genuine Windshield Pillar DCB500070PMA And Finisher Kit, Left Side With Rivets. MSRP $135. Estimated reproduction less than $50
https://www.roverparts.com/body-chas...CB500070PMAGK/
Genuine Windshield Pillar DCB500060PMA With Finisher Kit, Right Side With Rivets. Same as above.https://www.roverparts.com/body-chas...CB500060PMAGK/
Those are a few I find quick links for. The rear lower trim for the quarter panel to the bumper. The upper section that caps the rear bumper at the body. C pillar covers. The dash cover for cluster. Panel for the radio and climate control. And numerous other parts. I'm more concerned about exterior parts at the moment. Such as gutter trim prices but I have found a door trim roll that actually fits very well. I'll post once I find the link to it again. Allows to eliminate the harder plastics and replace with a flexible rubber trim that still give similar appearance. There are engine bay ann interior parts that tend to get brittle and crack as well. If go well metal printing maybe viable. If not I can make sheet metal replacements for some. Fortunately we have all kinds of tools in my shop to do just this sort of thing.
known as Center Air Intake Moulding JAK000010PMA MSRP $319 estimated cost to reproduce is about $150 or less
https://www.roverparts.com/body-chas...JAK000010PMAG/
Genuine Windshield Pillar DCB500070PMA And Finisher Kit, Left Side With Rivets. MSRP $135. Estimated reproduction less than $50
https://www.roverparts.com/body-chas...CB500070PMAGK/
Genuine Windshield Pillar DCB500060PMA With Finisher Kit, Right Side With Rivets. Same as above.https://www.roverparts.com/body-chas...CB500060PMAGK/
Those are a few I find quick links for. The rear lower trim for the quarter panel to the bumper. The upper section that caps the rear bumper at the body. C pillar covers. The dash cover for cluster. Panel for the radio and climate control. And numerous other parts. I'm more concerned about exterior parts at the moment. Such as gutter trim prices but I have found a door trim roll that actually fits very well. I'll post once I find the link to it again. Allows to eliminate the harder plastics and replace with a flexible rubber trim that still give similar appearance. There are engine bay ann interior parts that tend to get brittle and crack as well. If go well metal printing maybe viable. If not I can make sheet metal replacements for some. Fortunately we have all kinds of tools in my shop to do just this sort of thing.
I need the rear corner prices and am basically giving up trying to find real ones
#143
02-13-2023 | 09:41 PM
Recovery Vehicle
Joined: Apr 2017
Posts: 810
Likes: 168
From: Raleigh, NC
#144
05-14-2023 | 01:24 PM
Mudding
Joined: Aug 2021
Posts: 220
Likes: 130
From: Aurora, Colorado
Be kinda cool if we could scan and print these manual sunroof handles.... https://www.ebay.com/itm/125894548284
Windshield cowl for Discovery II 3D print files
The following users liked this post:
Roont (09-21-2023)
#148
09-27-2023 | 01:14 PM
7th Gear
Joined: May 2022
Posts: 7
Likes: 1
From: Sonoma County, CA, USA
#150
01-16-2024 | 11:56 AM
The following users liked this post:
TheLastOne (01-16-2024)