Discovery II Talk about the Land Rover Discovery II within.
Sponsored by:
Sponsored by:

Please Help!! Have six codes

Thread Tools
 
Search this Thread
 
  #11  
Old 03-05-2011, 01:00 PM
gavone1976's Avatar
Mudding
Thread Starter
Join Date: Feb 2011
Location: southern new jersey
Posts: 125
Likes: 0
Received 0 Likes on 0 Posts
Default

Could someone tell me what 02 sensors to buy and which 0 2 sensors go where?
I am pretty confident I can change them myself I just want to make sure I put the correct ones in the correct places?

Do i need a torque wrench to install them properly?
Do i just need to buy two front and two rear 02 sensors?(are there left and right ones?)

Should I put a cleaning agent in the gas tank?
 
  #12  
Old 03-06-2011, 09:07 AM
texmbr's Avatar
Rock Crawling
Join Date: Sep 2010
Location: Castroville, Texas
Posts: 294
Likes: 0
Received 1 Like on 1 Post
Default

Only buy a Bosch MAF. I tried cleaning (died in three days) and a aftermarket (continued to get codes). As far as 02's, you need to replace your MAF, clear you codes and then see if your 02's are OK. MAF needs to be ASAP because if bad it can kill perfectly good 02's. Your gonna need a torque wrench at some point. Get a inexpensive OBD2 code reade so you can read and clear codes. 38 bucks at autozone. I keep mine in my truck.
 
  #13  
Old 03-06-2011, 09:27 AM
gavone1976's Avatar
Mudding
Thread Starter
Join Date: Feb 2011
Location: southern new jersey
Posts: 125
Likes: 0
Received 0 Likes on 0 Posts
Default

where do you hook up the code reader at?
 
  #14  
Old 03-06-2011, 09:30 AM
gavone1976's Avatar
Mudding
Thread Starter
Join Date: Feb 2011
Location: southern new jersey
Posts: 125
Likes: 0
Received 0 Likes on 0 Posts
Default

I found one on BPUTAH for $145(Bosch),do I need the O-ring too?
 
  #15  
Old 03-06-2011, 09:40 AM
texmbr's Avatar
Rock Crawling
Join Date: Sep 2010
Location: Castroville, Texas
Posts: 294
Likes: 0
Received 1 Like on 1 Post
Default

The MAF should come with the O ring, but yes you do. The reader hooks up under the dash on the drivers side. You will see the connection and don't need to remove anything like interior panels.. Good luck. Those 02's are expensive and I would clear you problems one at a time.
 
  #16  
Old 03-06-2011, 10:41 AM
gavone1976's Avatar
Mudding
Thread Starter
Join Date: Feb 2011
Location: southern new jersey
Posts: 125
Likes: 0
Received 0 Likes on 0 Posts
Default

I cleaned the plastic housing of the MAF(inside and out) and hooked up the code scanner and reset the codes and the service engine soon light has gone away,lets see if it stays away for awhile.
It looked pretty new,the previous owner did a lot of the work himself on the rig , so maybe he never reset the codes.
 
  #17  
Old 03-06-2011, 05:12 PM
texmbr's Avatar
Rock Crawling
Join Date: Sep 2010
Location: Castroville, Texas
Posts: 294
Likes: 0
Received 1 Like on 1 Post
Default

It will take a little time to go through a drive cycle but you can check your code reader after a day or so even if your light is not on and you will get pending codes if you have any. Hope they are gone. Also check and make sure the filter cover and all the tube that runs to the upper intake is nice and tight.
 
  #18  
Old 03-06-2011, 06:08 PM
gavone1976's Avatar
Mudding
Thread Starter
Join Date: Feb 2011
Location: southern new jersey
Posts: 125
Likes: 0
Received 0 Likes on 0 Posts
Default

Light came back on,but with only 5 codes:
po174
po171
p1175
p1172
p0734
so po733 is now gone.
 
  #19  
Old 03-06-2011, 06:41 PM
gavone1976's Avatar
Mudding
Thread Starter
Join Date: Feb 2011
Location: southern new jersey
Posts: 125
Likes: 0
Received 0 Likes on 0 Posts
Default

Just ordered a new Bosch MAF $142.78 shipped.
 
  #20  
Old 03-07-2011, 07:47 AM
texmbr's Avatar
Rock Crawling
Join Date: Sep 2010
Location: Castroville, Texas
Posts: 294
Likes: 0
Received 1 Like on 1 Post
Default

Great..install (5 minutes) and clear your codes and good luck. Think you will be okay.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
G150driver
Retired - Private For Sale/Trade Classifieds
1
11-18-2014 09:47 AM
2fasttc
Retired - Private 'Wanted' Classifieds
0
04-09-2013 09:01 PM
Rovin4life
Discovery II
0
02-08-2010 06:32 AM
Torancis_LR
ROAMING WITH FRIENDS
3
12-24-2009 01:16 PM
Jerover
Discovery II
5
08-16-2008 02:40 PM



Quick Reply: Please Help!! Have six codes



All times are GMT -5. The time now is 07:24 PM.