Discovery II Talk about the Land Rover Discovery II within.
Sponsored by:
Sponsored by:

99 Disco II with 6 codes and three amigoes... please help where to start :)

Thread Tools
 
Search this Thread
 
  #11  
Old 12-10-2012 | 08:57 AM
Twistid's Avatar
Thread Starter
|
Drifting
Joined: Apr 2009
Posts: 33
Likes: 0
Default

Haha that was my question above, if I could use RTV or glue ... Yes I think I will try to rub a little RTV (silicone sealant) and tape to try to seal it up.
 
  #12  
Old 12-10-2012 | 09:01 AM
Twistid's Avatar
Thread Starter
|
Drifting
Joined: Apr 2009
Posts: 33
Likes: 0
Default

Also I think I will purchase just the two front O2 sensors for now. When I was searching the O2 sensor codes they all seemed to be front related.

P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)

Sensor 1 means front O2 sensor and Sensor 2 refers to rear sensor right? Bank 1 is driverside and Bank 2 is passenger?
 
  #13  
Old 12-10-2012 | 09:19 AM
lr2001silver's Avatar
Banned
Joined: Jul 2012
Posts: 1,533
Likes: 4
Default

Originally Posted by Twistid

Sensor 1 means front O2 sensor and Sensor 2 refers to rear sensor right? Bank 1 is driverside and Bank 2 is passenger?


Correct-da-mondo
 
  #14  
Old 12-10-2012 | 09:30 AM
lr2001silver's Avatar
Banned
Joined: Jul 2012
Posts: 1,533
Likes: 4
Default

Vac leak your talking about that hard plastic line runs behind the motor over to the driver side to the brake booster, you will find it towards the bottom of the booster and it has a big rubberish plug on that end. You could find the crack and cut the line there cut out a inch or two section and then go to hardware store and find a hose that's big enough to slip over original hard plastic line, go home and put some adhesive on the original line and slip new hose over both ends let seal and your good.
 
  #15  
Old 12-10-2012 | 09:48 AM
Twistid's Avatar
Thread Starter
|
Drifting
Joined: Apr 2009
Posts: 33
Likes: 0
Default

It's to close to the red clip to cut it off and slip on a larger hose to seal it up. I think I'll have to use silicone sealant to try to seal it up, if not I'll probably have to replace the whole thing. Can I pull out that red clip that goes into the head ?
 
  #16  
Old 12-10-2012 | 02:11 PM
jfall's Avatar
TReK
Joined: Mar 2012
Posts: 3,171
Likes: 44
Default

Put the codes into here

http://enginecodemaster.com
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Broken08
Discovery II
4
07-31-2015 03:49 PM
NWROVERS
Discovery II
6
03-10-2015 03:17 PM
buick56
Discovery I
1
05-15-2013 06:11 PM
04SSHD
Discovery II
8
04-11-2012 06:20 PM
matt3502
Discovery II
8
10-25-2011 10:41 PM



Quick Reply: 99 Disco II with 6 codes and three amigoes... please help where to start :)



All times are GMT -5. The time now is 06:30 PM.