Where to find "Heavy Duty" Shuttle Valve
#21
Alternator tested good at both places I had it tested, but I replaced it anyways since I have a lifetime warranty, saw no reason not to since I already had it removed, and while installing that we unbolted and cleaned/checked/modified a few of the major ground points.
It runs about 13.8 at idle with no lights on, and about 13.2 or so with the HID headlamps, the four rear facing lights on my rack, and six 135w Hella lights turned on all at the same time at idle.
It runs about 13.8 at idle with no lights on, and about 13.2 or so with the HID headlamps, the four rear facing lights on my rack, and six 135w Hella lights turned on all at the same time at idle.
#22
Alternator tested good at both places I had it tested, but I replaced it anyways since I have a lifetime warranty, saw no reason not to since I already had it removed, and while installing that we unbolted and cleaned/checked/modified a few of the major ground points.
It runs about 13.8 at idle with no lights on, and about 13.2 or so with the HID headlamps, the four rear facing lights on my rack, and six 135w Hella lights turned on all at the same time at idle.
It runs about 13.8 at idle with no lights on, and about 13.2 or so with the HID headlamps, the four rear facing lights on my rack, and six 135w Hella lights turned on all at the same time at idle.
Mine tested good, but they were covered in brake fluid. So I replaced the seals and also the switches. You might need to go in there again and test the switch. Or you might need to make sure that whatever that external ground you picked is good.
#23
Alternator tested good at both places I had it tested, but I replaced it anyways since I have a lifetime warranty, saw no reason not to since I already had it removed, and while installing that we unbolted and cleaned/checked/modified a few of the major ground points.
It runs about 13.8 at idle with no lights on, and about 13.2 or so with the HID headlamps, the four rear facing lights on my rack, and six 135w Hella lights turned on all at the same time at idle.
It runs about 13.8 at idle with no lights on, and about 13.2 or so with the HID headlamps, the four rear facing lights on my rack, and six 135w Hella lights turned on all at the same time at idle.
#24
Sorry, I do not. The Rave manual has a 'decent' enough amount of information to find what you need however.
......but back to the whole three amigos shuttle valve thing. I have a brand new Wabco shuttle valve switch sitting on my desk now, and when installing it I should still modify it and do the "Option B"?
......but back to the whole three amigos shuttle valve thing. I have a brand new Wabco shuttle valve switch sitting on my desk now, and when installing it I should still modify it and do the "Option B"?
Last edited by Street Wolf; 01-18-2012 at 02:20 AM.
#25
#26
Isn't the whole point of doing "option B" is the bypass/eliminate of svs circuit board which is not replaceable? My take on this is to do the option B fix plus the Falcon works over haul kit....thoughts??? If the svs circuit board part is available as part then you pretty much overhaul the whole ABS unit...I think...
Last edited by agthird; 01-18-2012 at 10:16 AM.
#27
Also what I did when I replaced my shuttle valve switches. It is kind of weird cutting and modifying the wiring on a brand new part, but that just means one less possible problem in the future. I also replaced the shuttle valve seals when I replaced the switches.
Thread
Thread Starter
Forum
Replies
Last Post
Blakesrover
Retired - Private For Sale/Trade Classifieds
0
02-20-2013 10:31 PM
bosshogt
Discovery II
4
02-02-2012 06:52 PM