So what did you do to your Disco today?
Drifting
Joined: Mar 2012
Posts: 31
Likes: 0
From: Richland Hills, TX.
It's still early but here's the list for today as on Sunday I Ann headed to Colorado
Brakes
Master cylinder
Valve cover gaskets
Upper rear ball joint
Steering shaft lower mines making a thunk every time you turn it the river coupler is toast
I sure there will be more after all its been a rover kind of week
Brakes
Master cylinder
Valve cover gaskets
Upper rear ball joint
Steering shaft lower mines making a thunk every time you turn it the river coupler is toast
I sure there will be more after all its been a rover kind of week
Recovery Vehicle
Joined: Jan 2012
Posts: 1,126
Likes: 11
From: mini soda
As requested, pictures of the Hyundai purge valve and replaced vacuum line:
https://i.imgur.com/2YTM4cU.jpg
https://i.imgur.com/3e21zvr.jpg
Please excuse the zip tie holding it in place. I've gone over a full tank of gas and no CEL...it's been running great.
https://i.imgur.com/2YTM4cU.jpg
https://i.imgur.com/3e21zvr.jpg
Please excuse the zip tie holding it in place. I've gone over a full tank of gas and no CEL...it's been running great.
I have AEL.
Does anyone think that matters?
Three Wheeling
Joined: Dec 2012
Posts: 68
Likes: 1
That's beyond my knowledge on this subject. Maybe compare the connector from what you have to the Amazon image? Or I can take a picture of it close up for you.
Recovery Vehicle
Joined: Jan 2012
Posts: 1,126
Likes: 11
From: mini soda
Naw, thats ok. Im pretty sure the connector is the same.
Camel Trophy
Joined: Nov 2009
Posts: 4,079
Likes: 227
From: IL
The reviews on Amazon show quite a few D2 owners using the same part so perhaps it would work for AEL trucks? I'm hoping.
Camel Trophy
Joined: Nov 2009
Posts: 4,079
Likes: 227
From: IL
I've never jacked up my truck to do anything with the radius or trailing arms. My truck is lifted though so I can slide under it on a creeper with no problem. I would chock the front wheels and leave them on the ground. I think you'll need to pull the track rod to drop the radius arms out, IIRC.
Recovery Vehicle
Joined: Jan 2012
Posts: 1,126
Likes: 11
From: mini soda
Another member said he fixed his CEL by spraying out the purge valve with brake cleaner and reinstalling.
If/when I can figure out what I did to kill my electrical system, Ill try these out and report back.
Rock Crawling
Joined: Oct 2012
Posts: 407
Likes: 0
From: San Diego, CA
It's been a productive day. Replaced my thermostat, sitting pretty at 196F instead of the 158 it had been. Old thermostat was most definitely stuck. Wonder what, if any, difference it'll make on fuel-efficiency...I've been averaging 220 miles/tank 
Fixed my rear step with magnets: https://landroverforums.com/forum/di...science-57183/
And installed my Hi-Lift on the rear bumper. I'm in the sand and don't need a lot of clearance; and it's as good a place as any until I get a rack or new bumper.
Here it is from the side; door clears easily when opening.
I plan on leaving it off the truck unless I'm heading out to play (and will probably lock it when I am).
Fixed my rear step with magnets: https://landroverforums.com/forum/di...science-57183/
And installed my Hi-Lift on the rear bumper. I'm in the sand and don't need a lot of clearance; and it's as good a place as any until I get a rack or new bumper.
Here it is from the side; door clears easily when opening.
I plan on leaving it off the truck unless I'm heading out to play (and will probably lock it when I am).
