What did you do with your DII today?
#5061
I had converted to DI blades, but one was bent at a car wash. I ordered the kit from Atlantic British and they are great. I had been using extra spring clip deals to get pressure. I had no ideas the springs on wiper arms worn out, I guess that makes sense.
if you have not done this, do it ASAP!
if you have not done this, do it ASAP!
#5062
They are called surewipe springs. How old are your wiper arms? I have the best Bosch wipers on with the new AB arms and the pressure is adequate. I’d get new arms before the springs. Not really much more expensive than good wiper blades.
#5063
They're about 2 years old. The issue I have is when using the newer beam blade wipers there isn't enough pressure on the middle of the blade to wipe away water (or snow/slush), so I've had to keep to the more traditional framed wiper blades. I'll have to check out Surewipe. Thanks!
#5064
They're about 2 years old. The issue I have is when using the newer beam blade wipers there isn't enough pressure on the middle of the blade to wipe away water (or snow/slush), so I've had to keep to the more traditional framed wiper blades. I'll have to check out Surewipe. Thanks!
#5066
Revamped the rear door a bit with a magnetic spice rack, and oil holders. Rivet nut tools come in handy all the time
Discovered that I botched the axle oil seal during my recent wheel hub replacement. Leaking oil. Not looking forward to doing that whole job... again.
Fix one thing, find another problem, rinse and repeat.
And I finished installing Terrafirma +3" 4-stage shocks on all corners.
Discovered that I botched the axle oil seal during my recent wheel hub replacement. Leaking oil. Not looking forward to doing that whole job... again.
Fix one thing, find another problem, rinse and repeat.
And I finished installing Terrafirma +3" 4-stage shocks on all corners.
#5067
They're about 2 years old. The issue I have is when using the newer beam blade wipers there isn't enough pressure on the middle of the blade to wipe away water (or snow/slush), so I've had to keep to the more traditional framed wiper blades. I'll have to check out Surewipe. Thanks!
Last edited by CollieRover; 04-01-2018 at 07:27 AM.
#5068
Installed Terrafirma 3" Lift on my 2004 Disco HSE7
A break in the Vancouver rain allowed me to install my Terrafirma 3" lift on my 2004 Disco HSE7. Messed it up on the rear DS side so fixed the coil that was upside down and completed the rest to give me a nice lift to fit my 32" Wildpeak ATV3 today.
- Question #1 - what do people do with the air-bag feeder tube after? Its currently sitting on top of the spring tower.
- Question #2 - I now have full-time Three Amigos, perhaps I overextended the ABS lines?? Guess I'll have to scan it? People have mentioned I need to reset SLABS, why?
- Question #1 - what do people do with the air-bag feeder tube after? Its currently sitting on top of the spring tower.
- Question #2 - I now have full-time Three Amigos, perhaps I overextended the ABS lines?? Guess I'll have to scan it? People have mentioned I need to reset SLABS, why?
Last edited by scottmb23; 04-01-2018 at 12:04 PM. Reason: Questions
#5070
Finally got my new tires on - Falken Wildpeak AT3 (275/65/18). I was expecting it to look more dramatic, guess that's what you get for sticking with 18" wheels. Going to need some spacers to stop the rubbing - any suggestions on 1/4" spacers or any will do??
3" Terrafirma lift and new tires
3" Terrafirma lift and new tires