So what did you do to your Disco today?
#692
09-04-2012, 07:39 PM
Rebuilt rear diff, had a little bit of play in pinion and was making some noise. Bearings looked fine, pattern looked fine, backlash looked fine.. 
Who knows.. So reset pinion preload and backlash at 10 thou hoping it will make it happy, we shall see!
Once that was done and back in the truck I tore into the 1.4 t-case. Need to clean it all up and get the bearings and seals. Here is a pic of the inside of the LT230 for those who have never seen the guts..
I'm going to pick up a LT77 and LT230. Not sure what I am going to do with the LT77 (maybe an Isuzu buggy?) as of yet but I believe the LT230 is a 1.4 as well..
Flushed and bled power steering pump again. This stupid chevy pump is annoyingly noisey. I put the expensive synthetic **** in there and it's still loud.... May go back to the ZF
Last but not least I'm about 90% on getting a Salisbury rear and re-building it with 30 spline D60 guts. Probably e-locker to match my future Toy hi-pinion plans for the front..
I'd go Toy rear but the Ring gear on a D60/Salisbury is 9 3/4"
here's a pic next to a regular rover diff...
That is all I have!
Who knows.. So reset pinion preload and backlash at 10 thou hoping it will make it happy, we shall see!Once that was done and back in the truck I tore into the 1.4 t-case. Need to clean it all up and get the bearings and seals. Here is a pic of the inside of the LT230 for those who have never seen the guts..
I'm going to pick up a LT77 and LT230. Not sure what I am going to do with the LT77 (maybe an Isuzu buggy?) as of yet but I believe the LT230 is a 1.4 as well..
Flushed and bled power steering pump again. This stupid chevy pump is annoyingly noisey. I put the expensive synthetic **** in there and it's still loud.... May go back to the ZF
Last but not least I'm about 90% on getting a Salisbury rear and re-building it with 30 spline D60 guts. Probably e-locker to match my future Toy hi-pinion plans for the front..
I'd go Toy rear but the Ring gear on a D60/Salisbury is 9 3/4"
here's a pic next to a regular rover diff...That is all I have!
Just for poop's and giggle's what are the part numbers for the bearings on the t-case and diffs?
#693
09-04-2012, 09:41 PM
#694
09-05-2012, 12:08 AM
Recovery Vehicle
Bearings are Fking expensive!! especially Timken stuff..
Last edited by Jake1996D1; 09-05-2012 at 12:11 AM.
#695
09-05-2012, 12:45 AM
Making progress on my rig. Finished the lift a few weeks back, then over the weekend, installed a new Heavy Duty rear driveshaft and rotoflex to joint conversion. Also put in my castor corrected radius arms!
Next up - gotta fix the clunk that showed up after the radius arms were installed
see my other post. I think I just need a sway bar drop kit.
Also on deck: steering damper relo, new tie-rod, drag link, and ends (rubber is split and cracked), then new tires BFG MT KM2 255/85R16.
Getting closer!
Next up - gotta fix the clunk that showed up after the radius arms were installed
see my other post. I think I just need a sway bar drop kit.Also on deck: steering damper relo, new tie-rod, drag link, and ends (rubber is split and cracked), then new tires BFG MT KM2 255/85R16.
Getting closer!
#696
09-05-2012, 07:06 AM
Started the transmission filter replacement last night...what a b*tch...I used a generous amount of PB blaster the day before and during and still broke several of the bolts holding the crossmember in place. Its not moving around much without love taps from a sledgehammer. Fluid is drained and the pan is loose but its not coming out...the crossmember is still in the way. Gonna work on it here some more in a couple hours when the suns up.
#697
09-05-2012, 08:07 AM
Started the transmission filter replacement last night...what a b*tch...I used a generous amount of PB blaster the day before and during and still broke several of the bolts holding the crossmember in place. Its not moving around much without love taps from a sledgehammer. Fluid is drained and the pan is loose but its not coming out...the crossmember is still in the way. Gonna work on it here some more in a couple hours when the suns up.
#698
09-05-2012, 02:33 PM
Recovery Vehicle
#700
09-05-2012, 03:56 PM
Recovery Vehicle
