Discovery I Talk about the Land Rover Discovery Series I within.

So what did you do to your Disco today?

Thread Tools
 
Search this Thread
 
  #2581  
Old 03-27-2014, 11:14 AM
tylor36's Avatar
Three Wheeling
Join Date: Jan 2010
Posts: 63
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by slomatt
I pulled out the alpine windows to fix some rust forming on the bottom edge. Not looking forward to putting them back in.

- Matt
Its easy, just pop out the middle rubber on the seal.
 
  #2582  
Old 03-27-2014, 12:10 PM
abran's Avatar
Baja
Join Date: Aug 2013
Location: Huntington Beach CA
Posts: 6,729
Received 721 Likes on 626 Posts
Default

When you put the middle insert back in, start with both cut ends together, the put all the corners in, then start pushing it in at different sections. If you start and one end and and work your way around, you will end up with too much/too little depending on your technique.
 
  #2583  
Old 03-27-2014, 01:23 PM
CUpgt's Avatar
Pro Wrench
Join Date: Apr 2010
Location: Upstate South Carolina
Posts: 1,450
Likes: 0
Received 2 Likes on 2 Posts
Default

Verdict is in, no cats, MagnaFlow, and a 6" resonator sounds damn good! Quiet at cruising speeds and has a nice smooth bark when you get into the pedal.
 
  #2584  
Old 03-27-2014, 05:54 PM
TOM R's Avatar
Baja
Join Date: Mar 2009
Location: south n.j. and ne va.
Posts: 5,735
Received 227 Likes on 197 Posts
Default

Good deal
 
  #2585  
Old 03-27-2014, 08:40 PM
fishEH's Avatar
Camel Trophy
Join Date: Nov 2009
Location: Lake Villa, IL
Posts: 4,079
Received 226 Likes on 195 Posts
Default

I installed the snorkel I got from Ian. Got the airbox all sealed up with silicone.... Maybe they could put a few more holes in that thing, there must have been 6.
Got my drive flange gaskets in the mail today so tomorrow I'll apply LocTite to the bolts and snug everything up back there after my lift wedges install.

Name:  IMAG1142_zpsvsgtrkya.jpg
Views: 81
Size:  86.6 KB

Name:  IMAG1127_zpskd2rt98s.jpg
Views: 62
Size:  83.4 KB
 
  #2586  
Old 03-28-2014, 01:12 AM
slomatt's Avatar
4wd Low
Join Date: Feb 2008
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by abran
When you put the middle insert back in, start with both cut ends together, the put all the corners in, then start pushing it in at different sections. If you start and one end and and work your way around, you will end up with too much/too little depending on your technique.
Thanks for the tips. I've got the windows out, tomorrow I'm hoping to find time to deal with the rust.

- Matt
 
  #2587  
Old 03-28-2014, 08:05 AM
TOM R's Avatar
Baja
Join Date: Mar 2009
Location: south n.j. and ne va.
Posts: 5,735
Received 227 Likes on 197 Posts
Default

Fish eh, aren't you guys concerned with starving the pinion bearing for oil with that much angle?
 
  #2588  
Old 03-28-2014, 09:20 AM
CUpgt's Avatar
Pro Wrench
Join Date: Apr 2010
Location: Upstate South Carolina
Posts: 1,450
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by TOM R
Fish eh, aren't you guys concerned with starving the pinion bearing for oil with that much angle?
My Pinion isn't steep at all in the rear and completely adjustable. Front points straight at the transfer case. Not uncommon on Rover fronts at all. Probably not the most ideal situation but I don't lose sleep over it.
Rear:
Name:  IMAG0600_zps85881856.jpg
Views: 114
Size:  73.5 KB
My rear wedges actually roll the spring seat over and point it slightly towards the front of my truck which is favorable with the rear axle pushed back about 2"
Front:
Name:  IMAG0673_zps5b77ecac.jpg
Views: 98
Size:  180.3 KB
 

Last edited by CUpgt; 03-28-2014 at 09:27 AM.
  #2589  
Old 03-28-2014, 09:44 AM
fishEH's Avatar
Camel Trophy
Join Date: Nov 2009
Location: Lake Villa, IL
Posts: 4,079
Received 226 Likes on 195 Posts
Default

Originally Posted by TOM R
Fish eh, aren't you guys concerned with starving the pinion bearing for oil with that much angle?
My rear arms are adjustable too, just like Ian's. And my truck is on jackstands in my pic so that's not necessarily how it will end up sitting with tires on it on the ground. But there are a fair amount of guys running DC front and rear shafts with the pinion pointed right at the TC.
That said, before I bolt in the passenger side axle/flange I'm going to lift it high and pump gear oil down the axle tube to overfill the diff.
 
  #2590  
Old 03-28-2014, 11:25 AM
CUpgt's Avatar
Pro Wrench
Join Date: Apr 2010
Location: Upstate South Carolina
Posts: 1,450
Likes: 0
Received 2 Likes on 2 Posts
Default

Originally Posted by fishEH
My rear arms are adjustable too, just like Ian's. And my truck is on jackstands in my pic so that's not necessarily how it will end up sitting with tires on it on the ground. But there are a fair amount of guys running DC front and rear shafts with the pinion pointed right at the TC.
That said, before I bolt in the passenger side axle/flange I'm going to lift it high and pump gear oil down the axle tube to overfill the diff.
I need to do that. Especially since I ditched axle seals and am running the hubs wet. Couldn't you just jack it up so the oil runs into the DS tube and overfill on the fill plug? Snorkel looks damn good too. You should thank fedex for breaking the plastic piece. It looks much better without.
 


Quick Reply: So what did you do to your Disco today?



All times are GMT -5. The time now is 10:17 PM.